E3D Revo High Temperature Hot Side Kit - Configurator
E3D's High Temperature Hot Side Kit for Rapid Change Revo is 500C capable and ready for high performance polymers.
This is a configurable product! Please read the notes below as you build out your selections!
E3D Revo High Temperature Hot Side Kit - Configurator
E3D's High Temperature Hot Side Kit for Rapid Change Revo is 500C capable and ready for high performance polymers.
HTX Hot side kits allow Revo users to upgrade their set-ups to enable reliable printing at higher temperatures with materials such as PEEK or PEI. High temperature, abrasive resistance Nozzles. Much like ObXidian, HTX nozzles have a hardened steel tip and copper spreader segment to optimize the transmission of heat to the heatsink. This assembly is then coated with Chromium Nitride to provide abrasive resistance up to 500°C. Fully customizable. Configure your ideal high temperature Hot End. Choose between a PT100 or PT1000, as well as either a high precision heater cartridge (up to 400C) or high temperature heater cartridge (up to 500C).
Rapid identification:
HTX nozzles are grey in color and have their sizes engraved into them with easy-to-read numbers, so there are no confusing identification markers to learn!
Please note:
· Revo™ Nozzles are not compatible with V6-style heater blocks · If your printer is not already using PT100 sensing then an amplifier board will be required to use the PT100 hot side variant.
· You may need to adjust your Z offset when changing nozzles.
· We do not recommend the use of abrasive materials with 0.25mm nozzles. The particle sizes, especially with fibres, can often be larger than 0.25mm, significantly increasing the risk of clogging the nozzle.
Key features:
· Maximum temperature: 400°C/500°C
· Filament diameter: 1.75mm
· Voltage: 24V
· Power: 40W or 65W
Compatible with:
Revo Micro, Revo Six, Revo Voron, Revo Creality, Revo Hemera XS, Revo Prusa MK3, Revo Prusa Mini, Revo MicroSwiss NG, Revo Biqu H2 V2, and Revo LGX.
Configuration Guide:
Step 1 - REQUIRED - Mandatory Option:
Required products regardless of your configuration
Option 1: High Temperature HTX Heater Block
Step 2 - Optional - Heater Type:
Choose the heater type that best fits your use-case
Option 1: E3D High Precision Heater 40W - Includes Extension Cable
Reach Hot End Temperatures of 400C
Option 2: E3D Ultra High Temp Heater 65W - Does not include Extension Cable
Reach Hot End Temperatures of 500C - Standard Design
Option 3: E3D Ultra High Temp Heater 65W (Angle Connection) - Includes Extension Cable
Reach Hot End Temperatures of 500C - Features a strain relieved 90 degree outlet at the heater cartridge
Option 4: Slice Engineering Mosquito Heater 50W - Includes Extension Cable
Reach Hot End Temperatures of 450C
Option 5: Slice Engineering Industrial Heater 50W - Includes Extension Cable
Reach Hot End Temperatures of 450C - Features a strain relieved 90 degree outlet at the heater cartridge
Step 3 - Optional - Thermistor Type:
Choose the thermistor type that best fits your use-case
Option 1: Slice Engineering RTD PT100 - Includes Extension Cable
For use in accurately reporting temperatures above 300C - Confirm compatibility with your firmware!
Option 2: Slice Engineering RTD PT1000 - Includes Extension Cable
For use in accurately reporting temperatures above 300C - Confirm compatibility with your firmware!
Step 4 - Optional - Nozzle Selection:
Choose your nozzle size
Option 1: HT Abrasive Revo Nozzle - Multiple Sizes to choose from
Want additional Nozzles? Add them from the product page here
Option 2: HT Copper (non abrasive resistant) Revo Nozzle - Multiple Sizes to choose from
Want additional Nozzles? Add them from the product page here
Step 5 - Optional - Heater Extension:
If your choice of heater cartridge from step 2 does not include an extension harness, add one here!
Option 1: E3D High Precision Heater Extension
Details:
Length: 1 Meter
Color(s): Green/Green Fiberglass
Termination 1: Molex Microfit 3.0 Connector - 2 Pin
Termination 2: Ferrules
You might also like